Digitrax

Digitrax BD4N DCC 4 Block Occupancy Detector   Low-cost, High-sensitivity DCC block-occupancy detection. Adjustable resistance/current detection section (DS) trip threshold. 8A capacity, suitable for all scales and track wiring configurations...

Digitrax BDL716 LocoNet Block Occupancy Detector - 16 Detection Sections The BDL716 is a cost effective LocoNet Occupancy Detector for 16 detection sections.  Lets you know when detection sections of your layout are occupied. When used in...

Digitrax BXP88 LocoNet Occupancy Detector with Transponding and Power Management - 8 Detection Sections   BXP88 makes adding detection and transponding to your layout easier than ever.  No more complicated wiring! DCC Occupancy Detection...

Digitrax BXPA1 LocoNet DCC Auto-Reverser with Detection, Transponding and Power Management   The BXPA1 is a combination DCC Auto-Revereser, occupancy detector, Transponding detector, and intelligent power manager. It is designed to make transponding...

Digitrax CARDEDGE CON 44 3 Pack Edge Connector   3 Pack Edge Connector for use with PM4 Series Boards, BDL16 Series Boards and SE8 Series Boards This is a replacement part that can be ordered through your dealer.  Digitrax does not repair this...

Digitrax LT1 Tester for Decoders & LocoNet Cables   It consists of a harness with 6 conductor Telco type wire with a male plug, a tester with a female 6 conductor jack, and a 100 Ohm 2 watt protection resistor. LT1 Features: Use as a...

Digitrax LT5C Tester Module (2pk) for BDL716, BDL16 Series Boards, BD4N, and other products   2 LT5C Tester Modules For use with BDL716, BDL16 Series Boards, BD4N, and other products  

Digitrax PS14 AC/DC Adapter 300ma 14VDC Power Supply   AC/DC Adapter 14V DC 300ma The PS14 is a 300ma, 14 Volt power supply for powering Digitrax accessories like the UP5, BDL168, DS64, SE8C, LNRP, UR90, UR91 UR92 and others  Universal AC...

Digitrax PTBK Pluggable Terminal Block Kit   Pluggable Terminal Blocks Replacement for lost or damaged Pluggable Terminal Blocks For use with products using Pluggable Terminal Blocks Includes: (1) 2 pin 3.5 mm Pluggable Terminal Block (1) 3 pin 3...

Digitrax RD2 Remote Sensing Diodes for BDL16 series occupancy detectors   RD2 Remote Sensing Diodes for BDL16 series occupancy detectors Remote sensing of 2 detection sections. Eliminates the need for long runs of heavy gauge wire between the...

Digitrax RX4 4-ZoneTransponding Receiver Add-on for BDL Series Detectors   The RX4 is a 4 zone transponder detector for use with Digitrax occupancy detection systems.  The RX4 enables you to not only see what blocks are occupied but also...

Digitrax SDCK Signal Driver Cable Kit   Materials for making 2 Signal Driver Cables for SE8C. Includes 30’of 10-wire Signal Driver ribbon cable & 8 10-Pin sockets. Use this kit to make signal driver cables to connect your SE8c to the...

Digitrax SE74 Signal Decoder   Fully connectorized installation. Optional support for DCC 9-Aspect control mode, including Lunars. Easy setup with Option Switches and LocoNet programming. Configurable for four solenoid or four slow-motion turnout...

Digitrax DCC SH2AB HO scale Mainline Signaling Kit The Digitrax Plug ‘N Play Signal Mast consists of a signal mast with one or two signal heads depending on mast configuration. Included with the kit are mounting boards and hardware that makes it...

Digitrax SHABC HO scale Turnout Signaling Kit   The Digitrax Plug ‘N Play Signal Mast consists of a signal mast with one or two signal heads depending on mast configuration. Included with the kit are mounting boards and hardware that makes it...

Digitrax SMBK Signal Mast Base Kit   Includes 3 Signal Masts that can be used as Signal Mast Bases in any scale or can be painted and detailed and used as N-scale signal masts.

Digitrax SMHK Signal Mounting Hardware Kit   Under layout mounting hardware for Signal Driver Cables and their sockets. 6 metal signal straps and 6 signal spacers. These handy bits of hardware hold your signal plugs at just the right distance from...

Digitrax SN2AB N scale Mainline Signaling Kit   The Digitrax Plug ‘N Play Signal Mast consists of a signal mast with one or two signal heads depending on mast configuration. Included with the kit are mounting boards...

Digitrax SNABC N scale Turnout Signaling Kit   The Digitrax Plug ‘N Play Signal Mast consists of a signal mast with one or two signal heads depending on mast configuration. Included with the kit are mounting boards and hardware that...

Digitrax TSMK Terminal Strip Mounting Kit   Includes 2 terminal strip boards with resistors for easy installation. Each terminal strip board can handle from 1 to 4 signal heads. Use this interface instead of Signal Mast Bases when you already have...

RR-CirKits SSSB-Digitrax Dual Decoder/Driver for Digitrax Dual Head 10-pin IDC Signals Dual head Decoder/Driver for 10 pin header equipped signals. Includes 3-1/2" M-F polarized pigtails.