Block Detection & Signaling

DCC Specialties "Block Watcher" Block Detection ModuleDCC Specialties and Integrated Signal Systems (ISS) collaborated to develop and design the BlockWatcher. The need was due to the fact that at the higher amperages required by high density users, most...

Digitrax LT1 Tester for Decoders & LocoNet Cables   It consists of a harness with 6 conductor Telco type wire with a male plug, a tester with a female 6 conductor jack, and a 100 Ohm 2 watt protection resistor. LT1 Features: Use as a...

Digitrax PS14 AC/DC Adapter 300ma 14VDC Power Supply   AC/DC Adapter 14V DC 300ma The PS14 is a 300ma, 14 Volt power supply for powering Digitrax accessories like the UP5, BDL168, DS64, SE8C, LNRP, UR90, UR91 UR92 and others  Universal AC...

Digitrax PTBK Pluggable Terminal Block Kit   Pluggable Terminal Blocks Replacement for lost or damaged Pluggable Terminal Blocks For use with products using Pluggable Terminal Blocks Includes: (1) 2 pin 3.5 mm Pluggable Terminal Block (1) 3 pin 3...

Digitrax RD2 Remote Sensing Diodes for BDL16 series occupancy detectors   RD2 Remote Sensing Diodes for BDL16 series occupancy detectors Remote sensing of 2 detection sections. Eliminates the need for long runs of heavy gauge wire between the...

Digitrax RX4 4-ZoneTransponding Receiver Add-on for BDL Series Detectors   The RX4 is a 4 zone transponder detector for use with Digitrax occupancy detection systems.  The RX4 enables you to not only see what blocks are occupied but also...

Digitrax SDCK Signal Driver Cable Kit   Materials for making 2 Signal Driver Cables for SE8C. Includes 30’of 10-wire Signal Driver ribbon cable & 8 10-Pin sockets. Use this kit to make signal driver cables to connect your SE8c to the...

Digitrax SE74 Signal Decoder   Fully connectorized installation. Optional support for DCC 9-Aspect control mode, including Lunars. Easy setup with Option Switches and LocoNet programming. Configurable for four solenoid or four slow-motion turnout...

Digitrax DCC SH2AB HO scale Mainline Signaling Kit The Digitrax Plug ‘N Play Signal Mast consists of a signal mast with one or two signal heads depending on mast configuration. Included with the kit are mounting boards and hardware that makes it...

Digitrax SHABC HO scale Turnout Signaling Kit   The Digitrax Plug ‘N Play Signal Mast consists of a signal mast with one or two signal heads depending on mast configuration. Included with the kit are mounting boards and hardware that makes it...

Digitrax SMBK Signal Mast Base Kit   Includes 3 Signal Masts that can be used as Signal Mast Bases in any scale or can be painted and detailed and used as N-scale signal masts.

Digitrax SMHK Signal Mounting Hardware Kit   Under layout mounting hardware for Signal Driver Cables and their sockets. 6 metal signal straps and 6 signal spacers. These handy bits of hardware hold your signal plugs at just the right distance from...

Digitrax SN2AB N scale Mainline Signaling Kit   The Digitrax Plug ‘N Play Signal Mast consists of a signal mast with one or two signal heads depending on mast configuration. Included with the kit are mounting boards...

Digitrax SNABC N scale Turnout Signaling Kit   The Digitrax Plug ‘N Play Signal Mast consists of a signal mast with one or two signal heads depending on mast configuration. Included with the kit are mounting boards and hardware that...

Digitrax TSMK Terminal Strip Mounting Kit   Includes 2 terminal strip boards with resistors for easy installation. Each terminal strip board can handle from 1 to 4 signal heads. Use this interface instead of Signal Mast Bases when you already have...

ESU 50094 ECoS Detector Feedback Module - 2 and 3 Rail Operation with RailCom   Our ECoSDetector feedback modules should be used to automate train operations. Beside the usual track occupancy detection, the train specific identification number can...

ESU 50095 ECoS Detector Feedback Extension Module If required, each ECoSDetector can be supplemented by a ECoSDetector Extension module, which can be easily connected to the ECoSDetector. Every ECoSDetector Extension module offers 32 transistor outputs...

ESU 50096 ECoS Detector Standard Feedback Module - 3-rail Operation   The ECoSDetector Standard is made for all model railroaders who look for a reliable and affordable feeback module without needing the expandable functions of the ECoSDetector. The...

ESU 50098 ECoS Detector RC Feedback Module - 2-rail Operation with RailCom   Train number detection The new ECoSDetector RC can monitor its 4 track sectors in a special way: with the aid of  the RailCom® technology (local detector) one can...

ESU 51840 SignalPilot DCC Accessory Decoder   The ESU SignalPilot decoder is a multi-protocol decoder designed primarily for switching daylight signals. It has 16 outputs to which micro lamps or LEDs (with series resistors) can be connected...

ESU 53452 LokProgrammer Set   You want to listen to the sound spectrum of your favourite loco, or the special sound of that loco around the corner in the yard – on your model railroad? No problem with ESU’s LokProgrammer! One...

NCE DCC AIU01 Auxiliary Input UnitThe Auxiliary Input Unit (AIU) provides a means of connecting external devices such as switch contacts, Block Detectors (BD20), or other sensors to the NCE Cab Bus or Command Station. These external devices can be...

NCE DCC BD20 Block Dectector UnitDetects DCC track current being drawn through a single track feeder. Isolated so there is no direct electrical connection to the track. Needs no external power for most operations. Can be connected to the NCE AIU01 or...

NCE DCC Dual Relay Board - High power Isolated Output For Switch8-Mk2   Dual relay board for isolated output of Switch8 or Switch-It.   2 Amp Relay for Connection to Switch-It or Switch 8 Accessory Decoder  

NCE DCC Light-It Function-Only Lighting And Signal DCC Decoder - Hardwire   The Light-It is a multi-purpose programmable DCC lighting decoder.  One Light-It contains three programmable lighting outputs with a complete array of lighting effects...

NCE DCC Light-It Function-Only Lighting And Signal DCC Decoder - Hardwire   The Light-It is a multi-purpose programmable DCC lighting decoder.  One Light-It contains three programmable lighting outputs with a complete array of lighting effects...

NCE DCC Light-It Function-Only Lighting And Signal DCC Decoder - Hardwire   The Light-It is a multi-purpose programmable DCC lighting decoder.  One Light-It contains three programmable lighting outputs with a complete array of lighting effects...

NCE DCC Mini Panel Automation ControllerUse one button to control multiple switches or macros on your NCE DCC system. You can have up to 30 pushbuttons, toggle switches, block detectors, etc. Can be connected for control of turnouts, signals, and other...

The ZIMO StEin Stationary Equipment Module   "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system...

The ZIMO StEin Stationary Equipment Module   "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system...

ZIMO Elektronik... World Class Turnout Control... Exceptional Value... ZIMO accessory decoders are used to operate and generate feedback from turnouts, light and semaphore signals, magnetic uncouplers and similar devices.ZIMO accessory decoders are...

ZIMO Elektronik... World Class Turnout Control... Exceptional Value... ZIMO accessory decoders are used to operate and generate feedback from turnouts, light and semaphore signals, magnetic uncouplers and similar devices.ZIMO accessory decoders are...

ZIMO Elektronik... World Class Turnout Control... Exceptional Value... ZIMO accessory decoders are used to operate and generate feedback from turnouts, light and semaphore signals, magnetic uncouplers and similar devices.ZIMO accessory decoders are...

ZIMO Elektronik... World Class Turnout Control... Exceptional Value... ZIMO accessory decoders are used to operate and generate feedback from turnouts, light and semaphore signals, magnetic uncouplers and similar devices.ZIMO accessory decoders are...

ZIMO Elektronik... World Class Servo Control... Exceptional Value... ZIMO servo decoders are used to operate and generate feedback from servo motors for controlling turnouts, crossing gates, semaphore signals, and similar devices.ZIMO servo...

ZIMO Elektronik... World Class Servo Control... Exceptional Value... ZIMO servo decoders are used to operate and generate feedback from servo motors for controlling turnouts, crossing gates, semaphore signals, and similar devices.ZIMO servo...

The ZIMO StEin Stationary Equipment Module "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system components; At...

The ZIMO StEin Stationary Equipment Module "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system components; At...

The ZIMO StEin Stationary Equipment Module "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system components; At...

The ZIMO StEin Stationary Equipment Module "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system components; At...