Bulk Order

Digitrax BXPA1 LocoNet DCC Auto-Reverser with Detection, Transponding and Power Management   The BXPA1 is a combination DCC Auto-Revereser, occupancy detector, Transponding detector, and intelligent power manager. It is designed to make transponding...

Digitrax DS52 Dual Stationary Decoder for Snap Switches or Slow Motion Machines   Dual Stationary Decoder for Bi-polar, Snap Switches or Slow Motion Machines DS52 Features: Simple hook up and set up. Control 2 individual turnout machines. 2 Slow...

Digitrax DS74 Quad Switch Stationary Decoder   The DS74 Stationary Decoder allows you to install and operate your turnouts directly through any DCC system that has turnout control. From Solenoid turnout machines to slow motion motors, this...

Digitrax DS78V Stationary Servo Decoder - Eight Servo LocoNet & Accessory decoder for turnout control   The DS78V Stationary Decoder allows you to install and operate your turnouts directly through any DCC system that has turnout control...

Digitrax DSXC4 Input Interconnect Board for DS74   The DSXC4 is simple to install, wire or plug in, and begin using to control switches on your DS74. Features Input interconnect board for DS74. Provides plug and play connectivity for DS74 inputs...

Digitrax DCC DSXCP1 Fascia Mount Switch Control Device for the DS74   The DSXCP1 is simple way to add point-of-use interface to control switches on your DS74. Features Fascia mount Switch control device. Wire to DS74 input cable, or use DSXC4 for...

Digitrax PM74 Power Manager with Occupancy and Transponding Detection for 4 sub-districts   4 Power Manager sub-districts. Upgraded replacement for PM42, fully encased. Fully connectorized installation. Each Power sub-district / Detection Section...

Digitrax SE74 Signal Decoder   Fully connectorized installation. Optional support for DCC 9-Aspect control mode, including Lunars. Easy setup with Option Switches and LocoNet programming. Configurable for four solenoid or four slow-motion turnout...

ESU SwitchPilot Extension, Model Number 51801     If required, SwitchPilot can be augmented with the SwitchPilot Extension Modul: Plugged in at the side of the SwitchPilot, it offers four relay-driven outputs, used for switching potential-free...

ESU 51808 ABC Brake Section Adapter for SwitchPilot Extension   These adaptor boards greatly simplify set-up and wiring of ABC braking sections. They are simply plugged into the terminals of a SwitchPilot Extension. Every adaptor board can...

ESU 51809 Signal Adapter for SwitchPilot   Our SwitchPilot decoders cannot only control point mechanisms but also daylight signals. Most modern signals are equipped with LEDs. Usually the anode connections of multi-aspect signals are combined in...

ESU 51830 SwitchPilot 3 DCC Accessory Decoder   SwitchPilot 3 decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary...

ESU 51831 SwitchPilot 3 Plus DCC Accessory Decoder   SwitchPilot 3 Plus decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other...

ESU 51832 SwitchPilot 3 Servo DCC Accessory Decoder   SwitchPilot 3 servo decoders are optimized for stationary use on your system and can control up to eight RC servo drives. In order to facilitate the rather cumbersome configuration of magnetic...

ESU 51840 SignalPilot DCC Accessory Decoder   The ESU SignalPilot decoder is a multi-protocol decoder designed primarily for switching daylight signals. It has 16 outputs to which micro lamps or LEDs (with series resistors) can be connected...

NCE DCC "Q-Snap" Quad Twin Coil Stationary Switch Decoder FOR TWIN COIL SWITCH MACHINES ONLY   All new easy programming! Control for 4 twin coil solenoid type switch machines (Atlas, Peco, etc) Supports the full range of DCC accessory addresses...