Bulk Order

Digitrax PR4 USB to LocoNet Interface with SoundFX Decoder Programmer The PR4 makes decoder programming and interfacing your layout and computer easier than ever. The PR4 seamlessly switches between computer interface and decoder programming modes...

Digitrax PS2012E 20A 13.8-23VDC DCC Power Supply   This power supply replaces the PS2012 to meet new efficiency requirements for DC power supplies. It delivers more power with less heat for more efficient operation. The 20 amp PS2012E regulated...

Digitrax PS615 AC/DC Adapter 90W 6A 15VDC Power Supply   PS615 90W AC/DC 15VDC 6 amp power supply for use with all Digitrax Command Stations and Boosters operating at 5 amps. High-efficiency power supply 15 VDC output Accepts...

Digitrax PTBK Pluggable Terminal Block Kit   Pluggable Terminal Blocks Replacement for lost or damaged Pluggable Terminal Blocks For use with products using Pluggable Terminal Blocks Includes: (1) 2 pin 3.5 mm Pluggable Terminal Block (1) 3 pin 3...

Digitrax RD2 Remote Sensing Diodes for BDL16 series occupancy detectors   RD2 Remote Sensing Diodes for BDL16 series occupancy detectors Remote sensing of 2 detection sections. Eliminates the need for long runs of heavy gauge wire between the...

Digitrax Replacement BP600MH Ni-MH 600mAH 3.6v Battery Pack For DT602 & UT6   Nickel-Metal Hydride 600mAH 3.6v Rechargeable Battery Pack. Compatible with Digitrax throttles with 3-pin battery plug. Chargeable when inside Digitrax throttles, no...

Digitrax RX4 4-ZoneTransponding Receiver Add-on for BDL Series Detectors   The RX4 is a 4 zone transponder detector for use with Digitrax occupancy detection systems.  The RX4 enables you to not only see what blocks are occupied but also...

Digitrax SDCK Signal Driver Cable Kit   Materials for making 2 Signal Driver Cables for SE8C. Includes 30’of 10-wire Signal Driver ribbon cable & 8 10-Pin sockets. Use this kit to make signal driver cables to connect your SE8c to the...

Digitrax SE74 Signal Decoder   Fully connectorized installation. Optional support for DCC 9-Aspect control mode, including Lunars. Easy setup with Option Switches and LocoNet programming. Configurable for four solenoid or four slow-motion turnout...

Digitrax SMHK Signal Mounting Hardware Kit   Under layout mounting hardware for Signal Driver Cables and their sockets. 6 metal signal straps and 6 signal spacers. These handy bits of hardware hold your signal plugs at just the right distance from...

Digitrax STOWAWAY Throttle Holder For DT602 & UT6 (1 pk)   Bracket will hold: DT602, UT6 and other legacy Digitrax throttles. Access to LocoNet & Power Ports when stowed away. Stores throttle when not in use or when charging. Fascia mounted...

Digitrax STOWAWAY Throttle Holder For DT602 & UT6 (4 pk)   Bracket will hold: DT602, UT6 and other legacy Digitrax throttles. Access to LocoNet & Power Ports when stowed away. Stores throttle when not in use or when charging. Fascia mounted...

Digitrax T1W 3mm Warm White T1 LEDs (10/pk)   10 Pack Warm White T1 LEDs   Make your locomotive lights sparkle!  Use these beautiful warm white LEDs to replace the harsh blue white LEDs that are sometimes shipped with locomotives...

Digitrax TSMK Terminal Strip Mounting Kit   Includes 2 terminal strip boards with resistors for easy installation. Each terminal strip board can handle from 1 to 4 signal heads. Use this interface instead of Signal Mast Bases when you already have...

Digitrax UP7 LocoNet Universal Interconnect Panel   Plug and Play Universal fascia panel supporting LocoNet. Two RJ12 front panel Throttle jacks. Three RJ12 rear pass-through LocoNet jacks Supports throttle charging. Fully connectorized...

Digitrax UR90X LocoNet IR Infrared Receiver Front Panel Cost effective wireless operation with infrared technology UR90X is a front panel unit that is an infrared receiver.  All current production Digitrax throttles are factory equipped with...