Auto Reversers & Power Management

DCC Specialties FROG-AR Quad Output Frog Auto-ReverserThe Frog-AR is a quad frog auto reverser designed and built by DCC Specialties. It is easy to install and will automatically adjust the connected frog [up to four] to the correct polarity. Each frog...

DCC Specialties PSX-ARSC Power Shield Auto Reverser - Circuit Breaker - Snap Coil w/ FeedbackThe PSX series is a product of Larry Maier's 10 years experience in designing and producing intelligent, solid state, DCC circuit breakers and auto...

DCC Specialties PSXX-1 Power Shield Circuit Breaker - 1 BlockPowerShield XX Series Circuit Breakers for DCC You can purchase your PSX Circuit Breakers in three configurations: PSXX-1 DCC Solid State Power District Circuit Breaker, 1 Block, 0-10 Amps...

DCC Specialties PSXX-2 Power Shield Circuit Breaker - 2 BlockPowerShield XX Series Circuit Breakers for DCC You can purchase your PSX Circuit Breakers in three configurations: PSXX-1 DCC Solid State Power District Circuit Breaker, 1 Block, 0-10 Amps...

DCC Specialties PSXX-3 Power Shield Circuit Breaker - 3 Block   PowerShield XX Series Circuit Breakers for DCC You can purchase your PSX Circuit Breakers in three configurations: PSXX-1 DCC Solid State Power District Circuit Breaker, 1 Block, 0-10...

DCC Specialties PSXX-AC Power Shield Circuit Breaker for Lionel, American Flyer and MTH AC Powered Systems The PSXX-AC, an  AC Circuit Breaker with Intelligent, Solid State Block Detection and Network Feed Back For AC Use Only New! Advanced...

DCC Specialties PSXX-AR Power Shield Auto Reverser / Circuit Breaker / Tortoise   Our next generation of auto reversing circuit breakers are on their way! The DCC Specialties PSXX-AR and PSXX-ARSC take the venerable PSX-AR that you all know and love...

DCC Specialties PSXX-ARSC Power Shield Auto Reverser / Circuit Breaker / Snap   Our next generation of auto reversing circuit breakers are on their way! The DCC Specialties PSXX-AR and PSXX-ARSC take the venerable PSX-AR that you all know and love...

DCC Specialties RRampMeter DCC Amp/Volt Meter Ver.1RRampMeter is now marketed by DCC Specialties! The only inexpensive device that accurately measures DCC Volts/Amps. Also measures AC and DC Volts/Amps. Costs less than DVMs that cannot measure DCC. Ver...

DCC Specialties RRampMeter DCC Amp/Volt Meter Ver.2RRampMeter is now marketed by DCC Specialties! The only inexpensive device that accurately measures DCC Volts/Amps. Also measures AC and DC Volts/Amps. Costs less than DVMs that cannot measure DCC. Ver...

DCC Specialties RRampMeter DCC Amp/Volt Meter Ver.3RRampMeter is now marketed by DCC Specialties! The only inexpensive device that accurately measures DCC Volts/Amps. Also measures AC and DC Volts/Amps. Costs less than DVMs that cannot measure DCC. Ver...

DCC Specialties RRampMeter DCC Amp/Volt Meter Ver.4RRampMeter is now marketed by DCC Specialties! The only inexpensive device that accurately measures DCC Volts/Amps. Also measures AC and DC Volts/Amps. Costs less than DVMs that cannot measure DCC. Ver...

Digitrax AR1 Auto Reversing Controller   The easiest most cost effective way to add automatic reversing to one section of your DCC layout.   AR1 Features: Cost effective automatic reversing for one reversing section or...

Digitrax BXP88 LocoNet Occupancy Detector with Transponding and Power Management - 8 Detection Sections   BXP88 makes adding detection and transponding to your layout easier than ever.  No more complicated wiring! DCC Occupancy Detection...

Digitrax BXPA1 LocoNet DCC Auto-Reverser with Detection, Transponding and Power Management   The BXPA1 is a combination DCC Auto-Revereser, occupancy detector, Transponding detector, and intelligent power manager. It is designed to make transponding...

Digitrax CARDEDGE CON 44 3 Pack Edge Connector   3 Pack Edge Connector for use with PM4 Series Boards, BDL16 Series Boards and SE8 Series Boards This is a replacement part that can be ordered through your dealer.  Digitrax does not repair this...

Digitrax LT1 Tester for Decoders & LocoNet Cables   It consists of a harness with 6 conductor Telco type wire with a male plug, a tester with a female 6 conductor jack, and a 100 Ohm 2 watt protection resistor. LT1 Features: Use as a...

Digitrax PM74 Power Manager with Occupancy and Transponding Detection for 4 sub-districts   4 Power Manager sub-districts. Upgraded replacement for PM42, fully encased. Fully connectorized installation. Each Power sub-district / Detection Section...

Digitrax PS14 AC/DC Adapter 300ma 14VDC Power Supply   AC/DC Adapter 14V DC 300ma The PS14 is a 300ma, 14 Volt power supply for powering Digitrax accessories like the UP5, BDL168, DS64, SE8C, LNRP, UR90, UR91 UR92 and others  Universal AC...

Digitrax PTBK Pluggable Terminal Block Kit   Pluggable Terminal Blocks Replacement for lost or damaged Pluggable Terminal Blocks For use with products using Pluggable Terminal Blocks Includes: (1) 2 pin 3.5 mm Pluggable Terminal Block (1) 3 pin 3...

Digitrax UP6Z LocoNet Universal Panel and 3 Amp Z Scale Voltage Reducer Features: 6 LocoNet Jacks for use with all scales Reduces track voltage by 4 or 6 volts at 3 amps for safer Z Scale locomotive opreration with Digitrax equipment Digitrax...

NCE DCC AR10 Auto Reverser with Circuit BreakerThe AR10 is an automatic reverse loop controller for DCC layouts. In addition it functions as a circuit breaker for the reverse loop. Very simple connections: Two wires to the main line and two wires to the...

NCE DCC CP6 Circuit Protection - 6 BlockBasic Circuit Protector. You can connect up to Six Outputs with 1 amp of protection per output. Light bulbs protect locomotivr and commadn station from damage. Highly visible indication when you have a short...

NCE DCC CP6 Replacement Lamps - 1APack of 6 replacement lamps for the CP6 circuit protector. 1 Amp  

NCE DCC EB1 v1.1 Electronic Circuit BreakerProvides short circuit protection for one power district. Can be used with most DCC systems. Default trip time is 30 times faster compared to the basic overload setting in all NCE systems. Electronic circuit...

NCE DCC Power Cab Auto-SW Program Track SwitchAuto SW: Adds a program track output to the Power Cab. Prevents accidental programming of locos on your mainline track when using Program Track mode. Automatically disconnects your main line when in...

NCE DCC Track Power Bus Snubber / RC Filter (2 pk)    Use with any DCC system to prevent large voltage spikes.  Reduces or eliminates voltage spikes on long runs of DCC bus wire  Protects decoders from damaging inductive voltage...

Tam Valley Depot DCC Circuit Breaker     This is the same board as the Dual Frog Juicer but confugured to work as a circuit breaker.  When there is a short it will cut off both rails at once.  This solves some problems where only...

Tam Valley Depot DCC Dual Frog Juicer/Auto-Reverser/Circuit Breaker     For all DCC systems including NCE PowerCab.     This board can be configured to use as an automatic polarity reverser for two frogs, a reversing loop, a...

Tam Valley Depot DCC Hex Frog Juicer (Polarity Reverser for Frogs)  For DCC systems 2 Amps to 8 Amps including NCE PowerCab.     This board can be configured to use as an automatic polarity reverser for six frogs, or a reverser for one...

Tam Valley Depot DCC Mono Frog Juicer (Polarity Reverser for Frogs) For all DCC systems including NCE PowerCab.     This board is an automatic polarity reverser for a single frog.  Setup is simple, connect two wires to the DCC bus and...

Tam Valley Depot DCC Turn On Module Soft Start Circuit For Large Inrush Currents of Sound Decoders and Stay Alive Decoders   If you have a lot of sound decoders and decoders with stay alive circuits on the track, they can confuse the booster...

TCS 1483 DCC Decoder AF1 Analog Filter     The Analog Filter 1 (AF1) is used to filter the DC signal leaving the power pack. This filter pack corrects flickering in lighting effects and low-speed auto-reversing. Only one AF1 is required to...