TCS - Train Control Systems
TCS 1530 WOWSound DCC Sound Decoder - WOW101-Diesel - NMRA 9-pin JST to Hardwire
- UPC:
- 879508004847
- MPN:
- 1530
- Condition:
- New
Save More With Volume Discounts…
Buy 5 - 9 | $103.45 each |
Buy 10 or above | $100.28 each |
Description
TCS WOWSound DCC Sound Decoder - WOW101-Diesel
The WOW101 is a universal decoder for locomotives with DCC-ready 9-pin plugs, or which cannot accommodate a motherboard or WOWKit. This decoder may be hard-wired or plugged directly into any locomotive with a 9-pin JST plug. The WOW101 is compatible with any T-Series harness, and also includes an auxiliary harness for attaching your speaker, AUX input, Keep Alive®, and for the additional lighting functions (F3 and F4).
NOTE: WOW101 decoders do not have on-board resistors. If you are going to use LED lighting with this product, you must include external resistors.
For a complete list of sounds, check out the "Sounds List" under the "Documents" tab.
- CD-Quality Sound: TCS' world-renowned CD-quality sound. 16 Bits of resolution at 44.1kHz sample rate.
- Back EMF Load Compensation: Provides superior slow speed control and high performance under load.
- Quiet Drive: Super-quiet motor control for "buzz" free motor performance.
- Variable Momentum: Allows you to make custom acceleration and deceleration curves.
- Incandescent Bulb Support: This decoder can be used with 12 Volt bulbs.
- Function Remapping: Buttons 0 through 12 may be used to control the lighting functions of this decoder.
- Programmable Lighting Effects: Choose from 20 separate user-programmable lighting effects!
- Dimmable Brightness: Configure multiple different brightness levels for your LED's or incandescent bulbs.
- Decoder Lock: Feature which prevents accidental/unwanted programming while activated.
- Airwire™ Compatible: Fully compatible with Airwire™ operation.
- Audio Assist®: TCS exclusive auditory feedback programming system. Program your decoder without the need tomemorize CV's!
- User-Loadable Speed Tables: Configure custom speed curves and set speed limits.
- Throttle Modes: Choose from multiple throttle modes to meet your operating needs.
- Proto Notch™: A WOWSound original feature which uses TCS’ exclusive auto-adjusting BEMF technology to automatically choose the active notch sound. Prototype Mode also offers dynamic sound volumes which accurately model the real-life equivalent. Also includes pre-programmed acceleration and deceleration values.
Specs
- Interface Type: Hard-Wire Direct-Plug (9-Pin JST)
- Dimensions (L x W x H): 1.35" x 0.658" x 0.22" or 34.29mm x 16.72mm x 5.59mm
- Scale: HO Scale
- Continuous/Peak: 1.3/2.0 Amp
- Total Functions: 6
- Function Rating: 100 mA
- 12V Outputs 6
Speaker Selection
- This decoder is optimized for 8 Ω speakers (not included).
- This decoder uses and audio amplifier capable of supplying up to 2 Watts of power to an 8 Ohm load at maximum volume. An 8 Ohm speaker with a 1 Watt minimum power rating is recommended for use with this decoder as it comes out of the package. If you are using an 8 Ohm speaker with a power rating of 2 Watts or less, you must reduce your master volume to prevent speaker failure or amplifier stress.
- The amplifier(s) on a WOWSound product can support speakers with impedance ratings as low as 4 Ohms. A reduction in impedance will require a higher power dissipation rating (more Watts) on said speaker. The minimum power requirement for a 4 Ohm speaker is 4 Watts. If you are using a 4 Ohm speaker with a power rating of 4 Watts or less, you must reduce your master volume to prevent speaker failure or amplifier stress.
- Speaker enclosures greatly increase speaker performance in most cases - improving the apparent volume by more efficiently directing the flow of air and reducing or eliminating destructive interference.
Decoder Specifications:
-
Size: 1.35 x .66 x 0.22 In (34.3 x 16.7 x 5.6 mm)
-
Connection: 9-Pin JST to Hardwire
-
Motor Rating: 1.0 Amp Continuous, 2.0 Amp Peak
-
Functions: (6) 100mA outputs (400mA Total)
-
BEMF: Yes
-
Protocol: NMRA DCC Compliant
-
Additional Features:
Additional Resources
MANUFACTURERS WEBSITE: |
|
SOUND CONFIGURATION & SOUND FILE RESOURCES: |
|
FIRMWARE & SOFTWARE RESOURCES: |
|
PRODUCT MANUALS & TECHNICAL DOCUMENT RESOURCES: |
|
MANUFACTURERS WARRANTY & REPAIRS: |
|
ADDITIONAL INFORMATION - DCC TIPS: |
|
ADDITIONAL INFORMATION (1): |
|
ADDITIONAL INFORMATION (2): |
Additional Information
PRODUCT CLASS : |
Standard (HO-S-O*) |
DECODER TYPE: |
Motor + Sound + Function |
DECODER INTERFACE (PRIMARY): |
Hardwire - Single Wires |
DECODER INTERFACE (SECONDARY): |
NMRA JST-Type |
SIZE-INCH (L x W x H): |
1.35 x 0.66 x 0.22 in |
SIZE-METRIC (L x W x H): |
34.3 x 16.7 x 5.6 mm |
MOTOR CURRENT (CONTINUOUS): |
1.3A |
MOTOR CURRENT (PEAK): |
2A |
FUNCTION CURRENT (MAX): |
100mA each |
NORMAL OUTPUT FUNCTIONS: |
6 |
LOGIC-LEVEL FUNCTIONS: |
0 |
SERVO OUTPUT FUNCTIONS: |
0 |
FUNCTION INPUTS: |
1 |
KEEP-ALIVE INTERFACE: |
Included - prewired* |
KA INPUT VOLTAGE (MAX): |
16V |
KA TOTAL CAPACITANCE: |
470uF |
SPEAKER INTERFACE: |
Hardwire - 2 Single Wires w/ Free Ends |
SOUND CHANNELS: |
7 |
SOUND PROCESSOR: |
16-bit |
SAMPLE RATE: |
44.1 kHz |
SOUND MEMORY: |
Preloaded |
AMP POWER (MAX): |
2W |
AMP IMPEDANCE: |
8 Ohms |
CV PROGRAMMING: |
Service Mode + P.O.M. |
FIRMWARE UPDATE: |
Yes - Factory Only |
SOUND FILE UPDATE: |
Optional CV Configurations by Model |
PROTOCOL: |
NMRA DCC |
BI-DIRECTIONAL COMMUNICATION: |
RailCom |
ADDITIONAL FEATURES: |
NA |
NOTES (1): |
* - Optional PnP WAUX-KA upgrade |
NOTES (2): |
NA |