Bulk Order

SPROG LCC ButtonLED LCC Network Test Module The ButtonLED is a small test board for our SPROG LCC I/O modules. It has 8 push buttons and 8 LEDs (Light Emitting Diodes) that are able to monitor and control the I/O channels. I/O channels can be configured...

SPROG LCC IO-LCC Network IO Interface Module The IO-LCC is a cost reduced version of the SERVOIO-LCC with differences in physical format and connector options. This User Guide covers the differences between the SERVOIO-LCC and IO-LCC. Features The main...

SPROG LCC POWER-LCC Network Power Module The power LCC allows power to be supplied to an LCC network. It is designed to be used with an external 12V 1 Amp PSU (Power Supply Unit). We supply a suitable regulated 12V supply. Connecting the POWER-LCC to the...

SPROG LCC SERVOIO-LCC Network Servo & IO Interface Module To be successful in using the SERVOIO-LCC you should be familiar with basic LCC topics, e.g. see the Introduction to LCC/OpenLCB https://www.sprog-dcc.co.uk/downloads/lcc/lcc-basics.pdf on our...

SPROG LCC TERM-LCC Network Termination Module The CAN bus of an LCC or OpenLCB network must be properly terminated for correct operation. The TERM-LCC is a convenient way to provide the required termination by simply plugging one TERM-LCC into the spare...

SPROG LCC USB-LCC Network to PC Interface Module Use a USB-LCC to interface your LCC/OpenLCB network to a WIndows, Linux or MacOS computer running JMRI. Galvanically isolated to protect your layout/computer, takes power from USB and requires power from...

The SPROG family of DCC devices   Controlling model railroad operation increasingly uses DCC, and the SPROG DCC Programmer offers the ideal solution for programming and maintaining your fleet of DCC-equipped locomotives, in any scale from Z to G!...

The SPROG family of DCC devices   Controlling model railroad operation increasingly uses DCC, and the SPROG DCC Programmer offers the ideal solution for programming and maintaining your fleet of DCC-equipped locomotives, in any scale from Z to G!...

Tam Valley Depot DCC Circuit Breaker     This is the same board as the Dual Frog Juicer but confugured to work as a circuit breaker.  When there is a short it will cut off both rails at once.  This solves some problems where only...

Tam Valley Depot DCC Dual Frog Juicer/Auto-Reverser/Circuit Breaker     For all DCC systems including NCE PowerCab.     This board can be configured to use as an automatic polarity reverser for two frogs, a reversing loop, a...

Tam Valley Depot DCC Hex Frog Juicer (Polarity Reverser for Frogs)  For DCC systems 2 Amps to 8 Amps including NCE PowerCab.     This board can be configured to use as an automatic polarity reverser for six frogs, or a reverser for one...

Tam Valley Depot DCC Mono Frog Juicer (Polarity Reverser for Frogs) For all DCC systems including NCE PowerCab.     This board is an automatic polarity reverser for a single frog.  Setup is simple, connect two wires to the DCC bus and...

Tam Valley Depot DCC Remote Aligner for Quad-LN     Used with the Quad-LN for alignment of servos.     Just one of these needed for all of your Quad-LNs.     Comes with a 10' cable which allows you to stand next to your...

Tam Valley Depot DCC Servo Centering Tool     Use this handy portable tool to keep your servos centered while you mount them under the layout.     The tool consists of a battery box connected to a small circuit board that...

Tam Valley Depot DCC Servo L-Bracket Mounting Kit This is a nice way to mount servos for operating a semaphore blade.   ...

Tam Valley Depot DCC SwitchWright Power Board 5 Volt 2 Amp DC to DC Converter If you aready have a DC accessory power bus and want to run SwitchWrights you can use this board to...