RR-CirKits LCC

RR-CirKits BOB-S Screw Terminal Break Out Board This board is designed to break out the 10 pin IDC ribbon cables into minature screw terminals for easy connections. (0.4" wide by 2.5" long).

RR-CirKits BOD-8-SM Block Occupancy Detector This new board is compatible with LCC node sample mode which allows using output drivers on the same I/O port. This board operates as a DCC occupancy...

RR-CirKits BOD4 Block Occupancy Detector This board operates as a DCC occupancy detector for 4 blocks using remote CT coils. It outputs logic levels, and has a RR-CirKits standard ribbon connector...

RR-CirKits BOD4-CP Block Occupancy Detector w/ Dual Turnout Driver This board operates as a DCC occupancy detector for 4 blocks using remote CT coils. It outputs logic levels, and has a RR-CirKits...

RR-CirKits CAB-10x100 10 Conductor Flat Ribbon Interface Cable - 1 ft 100' rolls, #28 AWG gray with red stripe on line one. Used to connect any daughter cards to the Tower Controller, TowerMan, or...

RR-CirKits CAB-10x100 10 Conductor Flat Ribbon Interface Cable - 100 ft 100' rolls, #28 AWG gray with red stripe on line one. Used to connect any daughter cards to the Tower Controller, TowerMan, or...

RR-CirKits CT-Coil Coil Transformers for Block Occupancy Detector Single CT (Current Transformer) coils for BOD-8-SM, BOD4 or BOD4-CP. These 100:1 toroid coils sense the track current on leads...

RR-CirKits CT-Coil-Set-4 Coil Transformers for Block Occupancy Detector Set of 4 CT (Current Transformer) coils for BOD4 or BOD4-CP. These 100:1 toroid coils sense the track current on leads passing...

RR-CirKits CT-Coil-Set-8 Coil Transformers for Block Occupancy Detector Set of 8 CT (Current Transformer) coils for BOD-8. These 100:1 toroid coils sense the track current on leads passing through...

RR-CirKits FOB-A Direct Drive Fan Out Board for LEDs This board is specifically designed to direct drive eight LED's from a single RR-CirKits port. It includes on board locations for current limiting...

RR-CirKits I/O Test-SM Sample Mode I/O Test Board This board contains 8 push button switches and 8 LED pairs. It is designed to quickly test the I/O ports on any of our boards such as the Tower LCC,...

RR-CirKits IDC-M10-LATCHx10 10-position IDC Male Socket w/ Latch - 10 pcs Box of 10 Insulation Displacement Connectors for use with 10 wire flat ribbon cable. Use with IDC-S10 to create extension...

RR-CirKits IDC-M10x10 10-position IDC Male Socket - 10 pcs Box of 10 Male Insulation Displacement Connectors for use with 10 wire flat ribbon cable. Use with IDC-S10 to create extension cables. Screw...

RR-CirKits IDC-S10x25 10-position IDC Female Socket - 25 pcs Box of 25 Insulation Displacement Connectors for use with 10 wire flat ribbon cable

RR-CirKits Isolator-8 8-line Input Isolation Board This board is specifically designed to isolate 12 volt DC voltages from the RR-CirKits logic level inputs. This allows connection of legacy (12V...

RR-CirKits OI-IB-8 8-line Input Opto-Isolation Board This board is normally used for block detection on three rail layouts. This version of the board includes internal current limiters. Useful...

RR-CirKits PS-S-15-1500 AC/DC Adapter 1500ma 15VDC Power Supply This high quality regulated switching power adapter powers any 15 Volt DC device up to 1.5 Amp. Made with quality in mind, this unit...

RR-CirKits RB-2 Dual Relay Board Relay Board - 2 is a Dual 10A DPDT relay board with logic level drivers. It is suitable for use with TC Mark II, TowerMan, Tower LCC, or other logic level output...

RR-CirKits RB-4 Quad Relay Board Relay Board - 4 is a Quad 10A SPDT relay board with logic level drivers. It is suitable for use with TC Mark II, TowerMan, Tower LCC, or other logic level output...

RR-CirKits SDB-4 4-Output Searchlight Driver Board This 4 output board is specifically designed to directly drive 4 four aspect signals utilizing bi-polar or three wire LED's and includes a yellow...

RR-CirKits SHD-2 8-Output Dual Signal Head Driver Board This 8 output signal head driver is a DCC accessory decoder. Includes prototypical lamp fade, brightness adjustment. Built in resistors allow...

RR-CirKits Signal LCC-32H Signal LCC-32H LCC (Layout Command and Control 8 line Input Output board Plus 32 Head controller with special effects

RR-CirKits Signal LCC-P Signal LCC-P LCC (Layout Command and Control 8 line Input Output board Plus 16 LED Driver with special effects

RR-CirKits Signal LCC-S Signal LCC-S LCC (Layout Command and Control 8 line Input Output board Plus 16 LED Driver with special effects

RR-CirKits SS-RGY-24 3mm Tri-Color Red - Green - Yellow LED w/ 24" Wire Leads This RGY LED is provided with four 24" long color coded #36 AWG wires. It may be fitted in place of a common T-1 LED with...

RR-CirKits SSSB-Atlas Dual Decoder/Driver for Atlas Dual Head Micro JST Signals Dual head Decoder/Driver for Atlas Micro JST equipped signals. Includes 3-1/2" M-F polarized pigtails.

RR-CirKits SSSB-Atlas Single Decoder/Driver for Atlas Single Head Micro JST Signals Single head Decoder/Driver for Atlas Micro JST equipped signals. Includes 3-1/2" M-F polarized pigtails.

RR-CirKits SSSB-Digitrax Dual Decoder/Driver for Digitrax Dual Head 10-pin IDC Signals Dual head Decoder/Driver for 10 pin header equipped signals. Includes 3-1/2" M-F polarized pigtails.

RR-CirKits SSSB-Dwarf Single Decoder/Driver for Showcase Miniatures 2194 Type SA. Dwarf Signals Single head Decoder/Driver for Showcase Miniatures Type SA. (SKU: 2194) Includes 3 color LED...

RR-CirKits SSSB-S Dual Decoder/Driver w/ Screw Terminals for Hardwire Signals Dual head Decoder/Driver with screw terminals for wire equipped signals. Includes 3-1/2" M-F polarized pigtails.

RR-CirKits SSSB-S Single Decoder/Driver w/ Screw Terminals for Hardwire Signals Single head Decoder/Driver with screw terminals for wire equipped signals. Includes 3-1/2" M-F polarized pigtails.

RR-CirKits Tower LCC General Purpose 16 Line Input/Output node for NMRA CAN bus LCC®. Logic level interface compatible with other standard RR-CirKits I/O modules. Boot Loader for user install able...

RR-CirKits Tower LCC+Q General Purpose 16 Line Input/Output node for NMRA CAN bus LCC® PLUS Text based Logic Engine. Logic level interface compatible with other standard RR-CirKits I/O modules. Boo