RR-CirKits

RR-CirKits 3TK2-4W I/O Module Mounting Track - Quad Position Wide Spacing This plastic mounting track is suitable for mounting four I/O modules to a flat surface with extra wiring space between...

RR-CirKits 3TK2-3W I/O Module Mounting Track - Three Position Wide Spacing This plastic mounting track is suitable for mounting three I/O modules to a flat surface with extra wiring space between...

RR-CirKits 3TK2-2W I/O Module Mounting Track - Dual Position Wide Spacing This plastic mounting track is suitable for mounting two I/O modules to a flat surface with extra wiring space between...

RR-CirKits 3TK2-6 I/O Module Mounting Track - Hex Position This plastic mounting track is suitable for mounting six I/O modules to a flat surface. (3 1/2" x 12") (I/O board not included)  

RR-CirKits 3TK2-4 I/O Module Mounting Track - Quad Position This plastic mounting track is suitable for mounting four I/O modules to a flat surface. (3 1/2" x 8") (I/O board not included)  

RR-CirKits 3TK2-3 I/O Module Mounting Track - Thee Position This plastic mounting track is suitable for mounting three I/O modules to a flat surface. (3 1/2" x 6") (I/O board not included)  

RR-CirKits 3TK2-2 I/O Module Mounting Track - Dual Position This plastic mounting track is suitable for mounting two I/O modules to a flat surface. (3 1/2" x 4") (I/O board not included)  

RR-CirKits 3TK2-1 I/O Module Mounting Track - Single Position This plastic mounting track is suitable for mounting a single I/O module to a flat surface. (3 1/2" x 2") (I/O board not included)  

RR-CirKits SPL-62 Quick Cable Lever Connector - 6 x 2 - 25pc Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 6 out. No more soldering under the layout. Fits AWG 28...

RR-CirKits SPL-42 Quick Cable Lever Connector - 4 x 2 - 25pc Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 4 out. No more soldering under the layout. Fits AWG 28...

RR-CirKits SPL-22 Quick Cable Lever Connector - 2 x 2 - 25pc Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 2 out. No more soldering under the layout. Fits AWG 28...

RR-CirKits SPL-62 Quick Cable Lever Connector - 6 x 2 Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 6 out. No more soldering under the layout. Fits AWG 28 - AWG...

RR-CirKits SPL-42 Quick Cable Lever Connector - 4 x 2 Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 4 out. No more soldering under the layout. Fits AWG 28 - AWG...

RR-CirKits SPL-22 Quick Cable Lever Connector - 2 x 2 Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 2 out. No more soldering under the layout. Fits AWG 28 - AWG...

RR-CirKits CAB-Servo M-F 39 Servo Extension Cable (M-F) - 39" This 39" cable may be used to extend the length of (M-M) servo cables.

RR-CirKits CAB-Servo M-M 20 Servo Connection Cable (M-M) - 20" This 20" cable may be used to connect two Quik-Link devices.

RR-CirKits CAB-Servo M-M 4 Servo Connection Cable (M-M) - 4" This 4" cable may be used to connect two Quik-Link devices.

Tortoise 800-6100 Slow Motion Switch Machine Remote Mount This mounting adapter may be used to mount a Tortoise remotely from the turnout location. Flexible cable linkage allows installing the remote...

RR-CirKits Tortoise-TAB-Package Tortoise Adapter Board w/ Tortoise 800-6000 Slow Motion Switch Machine Tortoise Adapter Board with new style Tortoise 800-6000 Slow Motion Switch Machine included...

RR-CirKits Tortoise-TAB Tortoise Adapter Board w/ Solderless Breakaway Connector The TAB is designed to provide a solder-less connection between the SMD-8 and Tortoise. It includes 10 pin daisy chain...

RR-CirKits Breakout-QL Quik-Link 10-pin IDC Breakout Board This Breakout board allows easy solder free connections from up to 8 Quik-Link devices to 10 pin I/O cables using 3 wire servo style cables...

RR-CirKits Tortoise-QL-Package Quik-Link Tortoise Driver-Adapter Board w/ Tortoise 800-6000 Slow Motion Switch Machine Tortoise Quik-Link with new style Tortoise 800-6000 Slow Motion Switch Machine...

RR-CirKits Tortoise-QL Quik-Link Tortoise Driver-Adapter Board w/ Solderless Breakaway Connector The Tortoise Quik-Link is a plug on Tortoise driver board. Breakaway connector inserts allow use on...

RR-CirKits Button Quik-Link Facia-mount Push Button - Indicator Light Unit The Button-QL is an LCC Sample Mode compatible indicator/switch unit. When used with an LCC node the switch function and...

RR-CirKits SSSB-Dwarf Single Decoder/Driver for Showcase Miniatures 2194 Type SA. Dwarf Signals Single head Decoder/Driver for Showcase Miniatures Type SA. (SKU: 2194) Includes 3 color LED...

RR-CirKits SSSB-S Single Decoder/Driver w/ Screw Terminals for Hardwire Signals Single head Decoder/Driver with screw terminals for wire equipped signals. Includes 3-1/2" M-F polarized pigtails.

RR-CirKits SSSB-S Dual Decoder/Driver w/ Screw Terminals for Hardwire Signals Dual head Decoder/Driver with screw terminals for wire equipped signals. Includes 3-1/2" M-F polarized pigtails.

RR-CirKits SSSB-Digitrax Dual Decoder/Driver for Digitrax Dual Head 10-pin IDC Signals Dual head Decoder/Driver for 10 pin header equipped signals. Includes 3-1/2" M-F polarized pigtails.

RR-CirKits SSSB-Atlas Dual Decoder/Driver for Atlas Dual Head Micro JST Signals Dual head Decoder/Driver for Atlas Micro JST equipped signals. Includes 3-1/2" M-F polarized pigtails.

RR-CirKits SSSB-Atlas Single Decoder/Driver for Atlas Single Head Micro JST Signals Single head Decoder/Driver for Atlas Micro JST equipped signals. Includes 3-1/2" M-F polarized pigtails.

RR-CirKits TC Mark II Tower Controller Mark II The TC-64 Tower Controller 64 line LocoNet® interface provides a simple and easy way to connect between the Digitrax LocoNet® bus and the layout...

RR-CirKits LocoBuffer-NG (Next Generation) Digitrax LocoNet® to USB type-A* Interface unit. 1,500 Volt Digital isolation between LocoNet and USB port. Type A* USB connector for direct computer...

RR-CirKits SS-RGY-24 3mm Tri-Color Red - Green - Yellow LED w/ 24" Wire Leads This RGY LED is provided with four 24" long color coded #36 AWG wires. It may be fitted in place of a common T-1 LED with...

RR-CirKits PS-S-15-1500 AC/DC Adapter 1500ma 15VDC Power Supply This high quality regulated switching power adapter powers any 15 Volt DC device up to 1.5 Amp. Made with quality in mind, this unit...

RR-CirKits IDC-M10-LATCHx10 10-position IDC Male Socket w/ Latch - 10 pcs Box of 10 Insulation Displacement Connectors for use with 10 wire flat ribbon cable. Use with IDC-S10 to create extension...

RR-CirKits IDC-M10x10 10-position IDC Male Socket - 10 pcs Box of 10 Male Insulation Displacement Connectors for use with 10 wire flat ribbon cable. Use with IDC-S10 to create extension cables. Screw...

RR-CirKits IDC-S10x25 10-position IDC Female Socket - 25 pcs Box of 25 Insulation Displacement Connectors for use with 10 wire flat ribbon cable.

RR-CirKits CAB-10x100 10 Conductor Flat Ribbon Interface Cable - 1 ft 100' rolls, #28 AWG gray with red stripe on line one. Used to connect any daughter cards to the Tower Controller, TowerMan, or...

RR-CirKits CAB-10x100 10 Conductor Flat Ribbon Interface Cable - 100 ft 100' rolls, #28 AWG gray with red stripe on line one. Used to connect any daughter cards to the Tower Controller, TowerMan, or...

RR-CirKits SMD-8 8-Output Stall Motor Driver Board LCC sample mode compatible. This 8 output, optically isolated, low current "H" bridge driver is designed for control of 8 stall motor switch...

RR-CirKits SHD-2 8-Output Dual Signal Head Driver Board This 8 output signal head driver is a DCC accessory decoder. Includes prototypical lamp fade, brightness adjustment. Built in resistors allow...

RR-CirKits SDB-4 4-Output Searchlight Driver Board This 4 output board is specifically designed to directly drive 4 four aspect signals utilizing bi-polar or three wire LED's and includes a yellow...

RR-CirKits RB-4 Quad Relay Board Relay Board - 4 is a Quad 10A SPDT relay board with logic level drivers. It is suitable for use with TC Mark II, TowerMan, Tower LCC, or other logic level output...

RR-CirKits RB-2 Dual Relay Board Relay Board - 2 is a Dual 10A DPDT relay board with logic level drivers. It is suitable for use with TC Mark II, TowerMan, Tower LCC, or other logic level output...

RR-CirKits OI-IB-8 8-line Input Opto-Isolation Board This board is normally used for block detection on three rail layouts. This version of the board includes internal current limiters. Useful...

RR-CirKits Isolator-8 8-line Input Isolation Board This board is specifically designed to isolate 12 volt DC voltages from the RR-CirKits logic level inputs. This allows connection of legacy (12V...

RR-CirKits I/O Test-SM Sample Mode I/O Test Board This board contains 8 push button switches and 8 LED pairs. It is designed to quickly test the I/O ports on any of our boards such as the Tower LCC,...

RR-CirKits BOB-S Screw Terminal Break Out Board This board is designed to break out the 10 pin IDC ribbon cables into minature screw terminals for easy connections. (0.4" wide by 2.5" long).

RR-CirKits FOB-C Dual Direct Drive Fan Out Board for LEDs This board is specifically designed to terminate the dual cable, eight stall motor, connections from a single SMD-8 board. It includes on...

RR-CirKits FOB-A Direct Drive Fan Out Board for LEDs This board is specifically designed to direct drive eight LED's from a single RR-CirKits port. It includes on board locations for current limiting...

RR-CirKits CT-Coil Coil Transformers for Block Occupancy Detector Single CT (Current Transformer) coils for BOD-8-SM, BOD4 or BOD4-CP. These 100:1 toroid coils sense the track current on leads...

RR-CirKits CT-Coil-Set-4 Coil Transformers for Block Occupancy Detector Set of 4 CT (Current Transformer) coils for BOD4 or BOD4-CP. These 100:1 toroid coils sense the track current on leads passing...

RR-CirKits CT-Coil-Set-8 Coil Transformers for Block Occupancy Detector Set of 8 CT (Current Transformer) coils for BOD-8. These 100:1 toroid coils sense the track current on leads passing through...

RR-CirKits BOD-8-SM Block Occupancy Detector This new board is compatible with LCC node sample mode which allows using output drivers on the same I/O port. This board operates as a DCC occupancy...

RR-CirKits BOD4-CP Block Occupancy Detector w/ Dual Turnout Driver This board operates as a DCC occupancy detector for 4 blocks using remote CT coils. It outputs logic levels, and has a RR-CirKits...

RR-CirKits BOD4 Block Occupancy Detector This board operates as a DCC occupancy detector for 4 blocks using remote CT coils. It outputs logic levels, and has a RR-CirKits standard ribbon connector...

RR-CirKits Signal LCC-P Signal LCC-P LCC (Layout Command and Control 8 line Input Output board Plus 16 LED Driver with special effects Signal LCC-P features: 16 Led drivers plus 8 line Input/Output...

RR-CirKits Signal LCC-S Signal LCC-S LCC (Layout Command and Control 8 line Input Output board Plus 16 LED Driver with special effects Signal LCC-S features: 16 Led drivers plus 8 line Input/Output...

RR-CirKits Signal LCC-32H Signal LCC-32H LCC (Layout Command and Control 8 line Input Output board Plus 32 Head controller with special effects Signal LCC-32H features: 32 Head signal controller...

RR-CirKits Tower LCC+Q General Purpose 16 Line Input/Output node for NMRA CAN bus LCC® PLUS Text based Logic Engine. Logic level interface compatible with other standard RR-CirKits I/O modules...

RR-CirKits Tower LCC General Purpose 16 Line Input/Output node for NMRA CAN bus LCC®. Logic level interface compatible with other standard RR-CirKits I/O modules. Boot Loader for user install...

RR-CirKits LCC VampMeter LCC Voltmeter and Ammeter features: Easily measure your CAN bus power. Size: 1-7/8" x 1-1/8" overall. Dual 4 digit continuous readout. Red and blue display. Includes a...

RR-CirKits LCC Repeater LCC Repeater features: Bit level repeater connects two LCC ® CAN bus segments. Adds two branch segments to an existing LCC ® network segment for improved node inter...

RR-CirKits LCC Starter Kit Introductory price for a LCC Buffer-USB, a Power-Point, 2 Terminators, includes 1' LCC cable and USB cable.

RR-CirKits LCC Buffer-USB NMRA CAN bus LCC® to USB interface. 2,500 Volt Digital isolation between CAN bus LCC® and USB port. Simplify your LCC configuration and/or use a PC based CTC...

RR-CirKits LCC Terminator Pair NMRA CAN bus LCC® Termination Pair. May be used to provide the required termination at each end of the CAN bus LCC® Balanced CAN termination provides the best...

RR-CirKits LCC Power-Point LCC Power-Point ties together 2 LCC jacks, a Traffic Monitor, and a power supply. Create a powered LCC bus for simple wiring by powering your LCC Nodes over the cable. The...

RR-CirKits LCC-LocoNet Gateway LCC (Layout Command and Control) 1024 function LCC – LocoNet translator LCC-LocoNet Gateway Message level gateway connects the LCC ® CAN bus and the Digitrax...