Stationary Accessory & Switch Decoders

DCC Specialties "Jack Wabbit Quad" Stationary Accessory DecoderThe Jack Wabbit is a Quad version of our popular Hare and Wabbit Intelligent Accessory Decoders. This decoder has four fully functional intelligent decoders on one printed circuit board. The...

DCC Specialties "Jack Wabbit Quad" Stationary Accessory Decoder The Jack Wabbit is a Quad version of our popular Hare and Wabbit Intelligent Accessory Decoders. This decoder has four fully functional intelligent decoders on one printed circuit board...

DCC Specialties "Jack Wabbit Quad" Stationary Accessory Decoder The Jack Wabbit is a Quad version of our popular Hare and Wabbit Intelligent Accessory Decoders. This decoder has four fully functional intelligent decoders on one printed circuit board...

DCC Specialties Tortoise Buddy "Senior" Connection Adapter   The Tortoise Buddy Senior. Simple and Functional. DCC, AC & DC Power can be used with the Buddy Screw terminal connections make connecting power to the Buddy easy Wire the...

Digitrax CARDEDGE CON 44 3 Pack Edge Connector   3 Pack Edge Connector for use with PM4 Series Boards, BDL16 Series Boards and SE8 Series Boards This is a replacement part that can be ordered through your dealer.  Digitrax does not repair this...

Digitrax DS44 Basic Quad Stationary Decoder   Basic Quad Stationary Decoder for Slow Motion Turnout Machines, add cost effective DCC control to your slow motion turnouts. DS44 Features: No frills stationary decoder. Simple installation and set up...

Digitrax DS51K1 Stationary Decoder For Single Kato Unitrack Turnouts   DS51K1 Stationary Decoder For Single Kato Unitrack Turnouts, easy cost effective way to add DCC control to your Kato Unitrack Turnouts. DS51K1 Features:  Stationary Decoder...

Digitrax DS52 Dual Stationary Decoder for Snap Switches or Slow Motion Machines   Dual Stationary Decoder for Bi-polar, Snap Switches or Slow Motion Machines DS52 Features: Simple hook up and set up. Control 2 individual turnout machines. 2 Slow...

Digitrax DS74 Quad Switch Stationary Decoder   The DS74 Stationary Decoder allows you to install and operate your turnouts directly through any DCC system that has turnout control. From Solenoid turnout machines to slow motion motors, this...

Digitrax DS78V Stationary Servo Decoder - Eight Servo LocoNet & Accessory decoder for turnout control   The DS78V Stationary Decoder allows you to install and operate your turnouts directly through any DCC system that has turnout control...

Digitrax DSXC4 Input Interconnect Board for DS74   The DSXC4 is simple to install, wire or plug in, and begin using to control switches on your DS74. Features Input interconnect board for DS74. Provides plug and play connectivity for DS74 inputs...

Digitrax DCC DSXCP1 Fascia Mount Switch Control Device for the DS74   The DSXCP1 is simple way to add point-of-use interface to control switches on your DS74. Features Fascia mount Switch control device. Wire to DS74 input cable, or use DSXC4 for...

Digitrax DCC DSXSV9 9G Turnout Motion Control Servo for DS78V   The DSXSV9 9G Turnout or Motion Control Servo comes with mounting bracket and installation hardware.  It is simple to install, wire and plug in, and begin using to control...

Digitrax LT1 Tester for Decoders & LocoNet Cables   It consists of a harness with 6 conductor Telco type wire with a male plug, a tester with a female 6 conductor jack, and a 100 Ohm 2 watt protection resistor. LT1 Features: Use as a...

Digitrax LT5 Tester Module (2pk) for BDL16 Series Boards, BD4N, and other products   2 LT5 Tester Modules For use with BDL16 Series Boards, BD4N, and other products  

Digitrax PS14 AC/DC Adapter 300ma 14VDC Power Supply   AC/DC Adapter 14V DC 300ma The PS14 is a 300ma, 14 Volt power supply for powering Digitrax accessories like the UP5, BDL168, DS64, SE8C, LNRP, UR90, UR91 UR92 and others  Universal AC...

Digitrax PTBK Pluggable Terminal Block Kit   Pluggable Terminal Blocks Replacement for lost or damaged Pluggable Terminal Blocks For use with products using Pluggable Terminal Blocks Includes: (1) 2 pin 3.5 mm Pluggable Terminal Block (1) 3 pin 3...

ESU SwitchPilot Extension, Model Number 51801     If required, SwitchPilot can be augmented with the SwitchPilot Extension Modul: Plugged in at the side of the SwitchPilot, it offers four relay-driven outputs, used for switching potential-free...

ESU Precision Servo Motor, Model Number 51804   The Precision Servo Motor is a high-performance and noiseless actuator, introduced by ESU, suitable for the SwitchPilot decoders. It uses a highly-developed remote control (RC) technique and is...

ESU Precision Servo Motor - Metal, Model Number 51805   ESU proudly presents a further, newly-developed servo motor for all ambitious model railway fans. The „Precision Servo Motor - Metal“ is preferred by all model railroaders who look...

ESU 51806 Linear Servo Motor   This linear servo in the dimensions 26mm x 22.5mm x 10.8mm is primarily intended for installation in electric locomotives in order to subsequently make the pantographs raised and lowered. The mechanics enable very...

ESU 51808 ABC Brake Section Adapter for SwitchPilot Extension   These adaptor boards greatly simplify set-up and wiring of ABC braking sections. They are simply plugged into the terminals of a SwitchPilot Extension. Every adaptor board can...

ESU 51809 Signal Adapter for SwitchPilot   Our SwitchPilot decoders cannot only control point mechanisms but also daylight signals. Most modern signals are equipped with LEDs. Usually the anode connections of multi-aspect signals are combined in...

ESU Servo Motor Extension Cable, Model Number 51810   With the Servo Extension Cable you are able to lengthen your Precision Servo Motor by up to 75cm.   3-pole J/R plug on socket J/R / Futaba, Length: 75cm    

ESU 51830 SwitchPilot 3 DCC Accessory Decoder   SwitchPilot 3 decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary...

ESU 51831 SwitchPilot 3 Plus DCC Accessory Decoder   SwitchPilot 3 Plus decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other...

ESU 51832 SwitchPilot 3 Servo DCC Accessory Decoder   SwitchPilot 3 servo decoders are optimized for stationary use on your system and can control up to eight RC servo drives. In order to facilitate the rather cumbersome configuration of magnetic...

ESU 53452 LokProgrammer Set You want to listen to the sound spectrum of your favourite loco, or the special sound of that loco around the corner in the yard – on your model railroad? No problem with ESU’s LokProgrammer! One prerequisite: A...

NCE DCC "Q-Snap" Quad Twin Coil Stationary Switch Decoder FOR TWIN COIL SWITCH MACHINES ONLY   All new easy programming! Control for 4 twin coil solenoid type switch machines (Atlas, Peco, etc) Supports the full range of DCC accessory addresses...

NCE DCC "Snap It" Twin Coil Stationary Switch DecoderControl one twin coil switch machine. Has capacitive discharge for low current draw of track power. Provides connections for two "local control" pushbuttons. You can control switches from your cabs and...

NCE DCC "Switch-Kat" Kato Unitrack Stationary Switch DecoderYour Kato Unitrack and LGB remote control turnouts can now be DCC controlled. The Switch-Kat provides connections for optional switch position indicator lights and "local control" pushbuttons...

NCE DCC "Switch8-Mk2" Stall Motor Stationary Switch DecoderEasy programming with no jumpers. On board LED display. Control for 8 Tortoise switch machines. Remembers the position of switch during power outages. Supports the full range of DCC accessory...

NCE DCC "SwitchIt-Mk2" Stall Motor Stationary Switch DecoderFOR STALL MOTOR MACHINES ONLY, NOT FOR USE WITH TWIN COIL SWITCH MACHINES  All new easy programming! Control for 2 Tortoise switch machines Remembers the position of switch during power...

NCE DCC Button-Board - Local Push Button Add-On For Switch8-Mk2Add up to 16 push buttons to Switch8-Mk2 - Accomodate N.O. Pushbuttons or toggle switches - Simple hook up, 3 wires to Switch8-Mk2.  

NCE DCC Dual Relay Board - High power Isolated Output For Switch8-Mk2   Dual relay board for isolated output of Switch8 or Switch-It.   2 Amp Relay for Connection to Switch-It or Switch 8 Accessory Decoder  

RR-CirKits BOB-S Screw Terminal Break Out Board This board is designed to break out the 10 pin IDC ribbon cables into minature screw terminals for easy connections. (0.4" wide by 2.5" long).

RR-CirKits Breakout-QL Quik-Link 10-pin IDC Breakout Board This Breakout board allows easy solder free connections from up to 8 Quik-Link devices to 10 pin I/O cables using 3 wire servo style cables. Also compatible with Berrett Hill products.

RR-CirKits Button Quik-Link Facia-mount Push Button - Indicator Light Unit The Button-QL is an LCC Sample Mode compatible indicator/switch unit. When used with an LCC node the switch function and indicator function may be controlled separately over the...

RR-CirKits CAB-10x100 10 Conductor Flat Ribbon Interface Cable - 1 ft 100' rolls, #28 AWG gray with red stripe on line one. Used to connect any daughter cards to the Tower Controller, TowerMan, or LNCP boards. Also used to connect signals to the 4ASD-4...

RR-CirKits CAB-10x100 10 Conductor Flat Ribbon Interface Cable - 100 ft 100' rolls, #28 AWG gray with red stripe on line one. Used to connect any daughter cards to the Tower Controller, TowerMan, or LNCP boards. Also used to connect signals to the 4ASD-4...

RR-CirKits CAB-Servo M-F 39 Servo Extension Cable (M-F) - 39" This 39" cable may be used to extend the length of (M-M) servo cables.

RR-CirKits CAB-Servo M-M 20 Servo Connection Cable (M-M) - 20" This 20" cable may be used to connect two Quik-Link devices.

RR-CirKits CAB-Servo M-M 4 Servo Connection Cable (M-M) - 4" This 4" cable may be used to connect two Quik-Link devices.

RR-CirKits FOB-C Dual Direct Drive Fan Out Board for LEDs This board is specifically designed to terminate the dual cable, eight stall motor, connections from a single SMD-8 board. It includes on board jumpers to select common positive or common negative...

RR-CirKits I/O Test-SM Sample Mode I/O Test Board This board contains 8 push button switches and 8 LED pairs. It is designed to quickly test the I/O ports on any of our boards such as the Tower LCC, Mark II, various of the WorkMan series SSB boards, and...

RR-CirKits IDC-M10-LATCHx10 10-position IDC Male Socket w/ Latch - 10 pcs Box of 10 Insulation Displacement Connectors for use with 10 wire flat ribbon cable. Use with IDC-S10 to create extension cables. Screw ears allow easy mounting to the layout.

RR-CirKits IDC-M10x10 10-position IDC Male Socket - 10 pcs Box of 10 Male Insulation Displacement Connectors for use with 10 wire flat ribbon cable. Use with IDC-S10 to create extension cables. Screw ears allow easy mounting to the layout.

RR-CirKits IDC-S10x25 10-position IDC Female Socket - 25 pcs Box of 25 Insulation Displacement Connectors for use with 10 wire flat ribbon cable.

RR-CirKits Isolator-8 8-line Input Isolation Board This board is specifically designed to isolate 12 volt DC voltages from the RR-CirKits logic level inputs. This allows connection of legacy (12V style) logic and drivers. This board may be used for...

RR-CirKits PS-S-15-1500 AC/DC Adapter 1500ma 15VDC Power Supply This high quality regulated switching power adapter powers any 15 Volt DC device up to 1.5 Amp. Made with quality in mind, this unit outperforms similar products. Let RR-CirKits keep your...

RR-CirKits RB-2 Dual Relay Board Relay Board - 2 is a Dual 10A DPDT relay board with logic level drivers. It is suitable for use with TC Mark II, TowerMan, Tower LCC, or other logic level output devices. It requires 12V auxiliary power to supply the...

RR-CirKits RB-4 Quad Relay Board Relay Board - 4 is a Quad 10A SPDT relay board with logic level drivers. It is suitable for use with TC Mark II, TowerMan, Tower LCC, or other logic level output devices. It requires 12V auxiliary power to supply the...

RR-CirKits SMD-8 8-Output Stall Motor Driver Board LCC sample mode compatible. This 8 output, optically isolated, low current "H" bridge driver is designed for control of 8 stall motor switch machines. (E.g. Tortoises®) It can drive up to 100ma. per...

RR-CirKits Tortoise-QL Quik-Link Tortoise Driver-Adapter Board w/ Solderless Breakaway Connector The Tortoise Quik-Link is a plug on Tortoise driver board. Breakaway connector inserts allow use on older Tortoises with narrow paddle contacts. It connects...

RR-CirKits Tortoise-QL-Package Quik-Link Tortoise Driver-Adapter Board w/ Tortoise 800-6000 Slow Motion Switch Machine Tortoise Quik-Link with new style Tortoise 800-6000 Slow Motion Switch Machine included. (green board) The Tortoise Quik-Link is a plug...

RR-CirKits Tortoise-TAB Tortoise Adapter Board w/ Solderless Breakaway Connector The TAB is designed to provide a solder-less connection between the SMD-8 and Tortoise. It includes 10 pin daisy chain cable headers and channel selection jumpers. Breakaway...

RR-CirKits Tortoise-TAB-Package Tortoise Adapter Board w/ Tortoise 800-6000 Slow Motion Switch Machine Tortoise Adapter Board with new style Tortoise 800-6000 Slow Motion Switch Machine included. (green board) The TAB is designed to provide a solder-less...

SPROG LCC ButtonLED LCC Network Test Module The ButtonLED is a small test board for our SPROG LCC I/O modules. It has 8 push buttons and 8 LEDs (Light Emitting Diodes) that are able to monitor and control the I/O channels. I/O channels can be configured...

SPROG LCC SERVOIO-LCC Network Servo & IO Interface Module To be successful in using the SERVOIO-LCC you should be familiar with basic LCC topics, e.g. see the Introduction to LCC/OpenLCB https://www.sprog-dcc.co.uk/downloads/lcc/lcc-basics.pdf on our...

Tam Valley Depot DCC Remote Aligner for Quad-LN     Used with the Quad-LN for alignment of servos.     Just one of these needed for all of your Quad-LNs.     Comes with a 10' cable which allows you to stand next to your...

Tam Valley Depot DCC Servo Centering Tool     Use this handy portable tool to keep your servos centered while you mount them under the layout.     The tool consists of a battery box connected to a small circuit board that...

TCS 2018 BSM-1 Dual Switch Machine Accessory DecoderThe BSM-1 Accessory Decoder from TCS is a single-output switch controller designed for single turnouts, including wyes. This decoder can be found in current-generation DCC E-Z Track® from Bachmann...

TCS 2019 BSM-2 Dual Switch Machine Accessory DecoderThe BSM-2 Switch Controller from TCS is a single-output switch controller designed for two turnouts simultaneously, such as single-crossovers. This decoder can be found in current-generation DCC E-Z...

Tortoise 800-6100 Slow Motion Switch Machine Remote Mount This mounting adapter may be used to mount a Tortoise remotely from the turnout location. Flexible cable linkage allows installing the remote actuator above or below the table top and at varying...

The ZIMO StEin Stationary Equipment Module   "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system...

The ZIMO StEin Stationary Equipment Module   "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system...

ZIMO Elektronik... World Class Turnout Control... Exceptional Value... ZIMO accessory decoders are used to operate and generate feedback from turnouts, light and semaphore signals, magnetic uncouplers and similar devices.ZIMO accessory decoders are...

ZIMO Elektronik... World Class Turnout Control... Exceptional Value... ZIMO accessory decoders are used to operate and generate feedback from turnouts, light and semaphore signals, magnetic uncouplers and similar devices.ZIMO accessory decoders are...

ZIMO Elektronik... World Class Turnout Control... Exceptional Value... ZIMO accessory decoders are used to operate and generate feedback from turnouts, light and semaphore signals, magnetic uncouplers and similar devices.ZIMO accessory decoders are...

ZIMO Elektronik... World Class Turnout Control... Exceptional Value... ZIMO accessory decoders are used to operate and generate feedback from turnouts, light and semaphore signals, magnetic uncouplers and similar devices.ZIMO accessory decoders are...

ZIMO Elektronik... World Class Turnout Control... Exceptional Value... ZIMO accessory decoders are used to operate and generate feedback from turnouts, light and semaphore signals, magnetic uncouplers and similar devices.ZIMO accessory decoders are...

ZIMO Elektronik... World Class Turnout Control... Exceptional Value... ZIMO accessory decoders are used to operate and generate feedback from turnouts, light and semaphore signals, magnetic uncouplers and similar devices.ZIMO accessory decoders are...

ZIMO Elektronik... World Class Servo Control... Exceptional Value... ZIMO servo decoders are used to operate and generate feedback from servo motors for controlling turnouts, crossing gates, semaphore signals, and similar devices.ZIMO servo...

ZIMO Elektronik... World Class Servo Control... Exceptional Value... ZIMO servo decoders are used to operate and generate feedback from servo motors for controlling turnouts, crossing gates, semaphore signals, and similar devices.ZIMO servo...

The ZIMO StEin Stationary Equipment Module "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system components; At...

The ZIMO StEin Stationary Equipment Module "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system components; At...

The ZIMO StEin Stationary Equipment Module "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system components; At...

The ZIMO StEin Stationary Equipment Module "Stone" - modules ( St ationär- A directional modules) are of which are intended to be used together with a base unit of the ZIMO MX10 series as a digital central ZIMO digital control system components; At...